Efficient atom localization via probe absorption in an inverted-Y atomic system

The behaviour of atom localization in an inverted-Y atomic system is theoretically investigated. For the atoms interacting with a weak probe field and several orthogonal standing-wave fields, their position information can be obtained by measuring the probe absorption. Compared with the traditional scheme, we couple the probe field to the transition between the middle and top levels. It is found that the probe absorption sensitively depends on the detuning and strength of the relevant light fields. Remarkably, the atom can be localized at a particular position in the standing-wave fields by coupling a microwave field to the transition between the two ground levels.     

热处理对挤压态Mg-6Gd-5Y-1Zn合金组织与性能的影响

通过对Mg-6Gd-5Y-1Zn(质量分数,%)合金在固溶和时效处理状态下显微组织和力学性能的研究发现,α-Mg基体、沿挤压方向分布的条状18R-LPSO相、少量的Mg₂₄(GdYZn)₅ 相以及细层片状的14H-LPSO相构成了挤压态合金的组成相。挤压态合金经固溶(T4)处理后,一部分18R-LPSO相溶入基体,并且基体中的14H-LPSO相伸长同时粗化。挤压态合金经过固溶加时效(T6)处理后,大量β′相从α-Mg基体中析出。T6态合金的室温力学性能最好,其屈服强度、抗拉强度及伸长率分别为272 MPa、406 MPa和6.1%。β′相沉淀也发生在挤压态合金的直接人工时效(T5)处理过程,但相比于T6处理,14H-LPSO相和β′相在基体中的体积分数均偏低。     

Standing Surface Acoustic Wave (SSAW)‐Based Fluorescence‐Activated Cell Sorter

Microfluidic fluorescence‐activated cell sorters (μFACS) have attracted considerable interest because of their ability to identify and separate cells in inexpensive and biosafe ways. Here a high‐performance μFACS is presented by integrating a standing surface acoustic wave (SSAW)‐based, 3D cell‐focusing unit, an in‐plane fluorescent detection unit, and an SSAW‐based cell‐deflection unit on a single chip. Without using sheath flow or precise flow rate control, the SSAW‐based cell‐focusing technique can focus cells into a single file at a designated position. The tight focusing of cells enables an in‐plane‐integrated optical detection system to accurately distinguish individual cells of interest. In the acoustic‐based cell‐deflection unit, a focused interdigital transducer design is utilized to deflect cells from the focused stream within a minimized area, resulting in a high‐throughput sorting ability. Each unit is experimentally characterized, respectively, and the integrated SSAW‐based FACS is used to sort mammalian cells (HeLa) at different throughputs. A sorting purity of greater than 90% is achieved at a throughput of 2500 events s^?1. The SSAW‐based FACS is efficient, fast, biosafe, biocompatible and has a small footprint, making it a competitive alternative to more expensive, bulkier traditional FACS.     

基于XML的信息物理融合系统组件建模与仿真

信息物理融合系统（CPS）涉及多种计算模型的集成和协同工作，针对CPS设计方法不统一、重塑性差、复杂度高、难以协同建模验证等问题，提出一种结构化、可描述行为的异元组件模型。首先，用统一组件建模方法进行建模，解决模型不开放问题；然后，用可扩展标记语言（XML）规范描述各类组件，解决不同计算模型描述语言不一致和不可扩展问题；最后，用多级开放组件模型的协同仿真验证方式进行仿真验证，解决验证的不可协同问题。通过通用组件建模方法、XML组件规范描述语言以及验证工具平台XModel对医用恒温箱进行了建模、描述和仿真。医用恒温箱的案例表明，这种模型驱动建立可重塑异元组件并确认其设计正确性的过程，支持信息物理协同设计和边构建边纠正，可避免在系统实现过程中发现问题时再进行反复修改。     

含煤盆地深层“超饱和”煤层气形成条件

中国深层煤层气资源丰富，但总体勘探和认识程度较低，尚未形成较为系统的深层煤层气地质理论。通过解剖分析准噶尔盆地白家海凸起和鄂尔多斯盆地临兴区块深层"超饱和"煤层气井的试气/生产动态，估算原地游离气的含气量，分析了深层"超饱和"煤层气的形成条件。研究表明：①深层"超饱和"煤层气储层中除吸附气外，还含有原地游离气，用常规试气方法可直接获得气流，煤层气的产出不明显依赖于排水降压；②埋藏超过一定深度，在煤阶和温度的综合作用下，煤的吸附能力将随埋深的继续增加而降低，煤层中吸附气的饱和度有增加的趋势，在达到吸附饱和后，出现原地游离气并形成"超饱和"煤层气，盆地深层具有"超饱和"煤层气形成的优势条件；③由于地温梯度和压力梯度的不同，不同盆地"超饱和"煤层气出现的临界深度不同，异常高压和异常高热流可以降低深层"超饱和"煤层气形成的临界深度；④深层"超饱和"煤层气开发具有大大缩短见气时间、充分利用地层能量和累积产水量低等优势，有望成为未来煤层气勘探开发的一个重要领域。     

察尔汗盐湖区输电线路杆塔地基溶陷变形分析及防治措施

察尔汗盐湖区盐渍土的溶陷问题一直是困扰该区工程建设的难题.基于该区某输电线路地基溶陷变形事故的调查研究,从含盐量、盐渍土微观结构特征、土层密实度和渗透性、浸水时间和水径流条件、淡水侵蚀大小5方面内外因素分析了其对溶陷变形的控制影响和作用规律.在此基础上,探讨了溶陷变形机理、地基破坏模式以及防治措施,以期为该工程及后期电网工程提供指导和建议.     

Fabrication and characterizations of Cr3+-doped ZnGa2O4 transparent ceramics with persistent luminescence

0.5 at.% Cr:ZnGa₂O₄ precursor was synthesized by the co-precipitation method with nitrates as raw materials, using ammonium carbonate as the precipitant. Low-agglomerated Cr:ZnGa₂O₄ powders with an average particle size of 43 nm were obtained by calcining the precursor at 900℃ for 4 h. Using the powders as starting materials, 0.5 at.% Cr:ZnGa₂O₄ ceramics with an average grain size of about 515 nm were prepared by presintering at 1150℃ for 5 h in air and HIP post-treatment at 1100℃ for 3 h under 200 MPa Ar. The in-line transmittance of 0.5 at.% Cr:ZnGa₂O₄ ceramics with a thickness of 1.3 mm reaches 59.5% at the wavelength of 700 nm. The Cr:ZnGa₂O₄ ceramics can be effectively excited by visible light and produce persistent luminescence at 700 nm. For Cr:ZnGa₂O₄ transparent ceramics, the brightness of afterglow was larger than 0.32 mcd/m² after 30 min, which is far superior to that of Cr:ZnGa₂O₄ persistent luminescence powders.     

伊拉克A油田Asmari组混积型碳酸盐岩储层隔夹层研究

伊拉克A油田Asmari组为大型混积型碳酸盐岩油藏,发育灰岩、白云岩、砂岩、泥岩和硬石膏等多种岩性,储层复杂、非均质性强,存在多种类型的隔夹层。基于岩心、薄片、测井和分析测试等资料,对研究区隔夹层类型及特征展开综合分析,识别出了泥岩、硬膏岩和泥-微晶碳酸盐岩3类隔夹层。泥岩和硬石膏致密无孔隙、基本不具有渗流能力,对流体流动可以起到阻挡作用;泥-微晶碳酸盐岩属于细粒碳酸盐岩沉积,孔隙度低,但一般裂缝较发育,具有一定渗流能力,不能对流体起到有效的隔挡作用。硬石膏主要在油田中部及北部A段发育,其对油田北部储层纵向连通起到一定隔挡作用,导致纵向压力衰竭不一致。泥岩主要在C段顶部、B4和B1层发育,平面上主要在油田南部较发育。C段顶部发育一套厚度较大、稳定分布的泥岩隔层,将C段和上部B段及A段分隔为两个独立的油水系统,并有效阻挡了C段水层锥进到B段;B4和B1层泥岩较发育,但由于油田南部区域断层和裂缝较发育,导致泥岩隔夹层未能起到有效隔挡作用。搞清研究区隔夹层类型、分布及是否起隔挡作用,对A油田各区域各小层有效动用开发、见水规律研究具有很好的指导意义。